There are many times you wish to a specific device of your own to reduce volumes or any measurements of your concern. An example could be your audio equipment, deflections in a cantilevered stairway, or even the noisy tachometer of your motorbikes. For these adjustments, you may opt to use a potentiometer which is a variable resistor.
This type of circuitry is of great aid when wanting to divide volumes of voltages sent. To simplify, the specific device that you should have is called a voltage divider. This happens to be one of the most fundamental circuits you will be dealing with in the field of electronics.
Using two resistors, this divider shall allow you to turn a large voltage into a smaller one provided that you also have the value of input voltage. Understand how this device works need you to be familiar with the Ohms law which states, the direct current flowing in a conductor is directly proportional to the potential difference between its ends.
This divider has two main parts namely the circuit and the equation. To make it work, first, you should secure a circuit by putting in two resistors together. The equation, on one hand, allows you to calculate the output after you have found the ratio of both resistors while considering the input volt as another variable.
Though you can buy your own device, creating a portable one can be a better choice as it helps you save. For this, you have to secure leads, resistors, a 9V battery, alligator clamps, voltmeter and its connectors. In addition, you have to ensure that you get at most the standard battery voltage which is 9.
Start by connecting one lead to a red lead of a 9V battery with an alligator clamp. Then using another lead, do the same steps but this time using the black lead of the connector. After, you can twist the free end of each resistor together.
Make sure that you have provided a solid twist for it by clamping an alligator clamp on it. Then look at the positive and negative terminals of the battery. When found, attach the red wire to the positive and the black wire to the negative. Then turn your meter on.
The positive voltage terminal of your circuit would be the connector which holds the twisted resistors together in place. On one hand, the negative terminal retains to be the negative source. Using the given equation, the new Volt count of your 9V battery goes down to 3V.
When doing this procedure, always see to it that you have unhooked an end of a divider or unplugged your battery to prevent it from draining. More so, be cautious when working with these types of wiring especially the ones which are still plugged into its outlet because it may result in electrocution. In this case, however, there is not much danger in a 9V energy source.
This type of circuitry is of great aid when wanting to divide volumes of voltages sent. To simplify, the specific device that you should have is called a voltage divider. This happens to be one of the most fundamental circuits you will be dealing with in the field of electronics.
Using two resistors, this divider shall allow you to turn a large voltage into a smaller one provided that you also have the value of input voltage. Understand how this device works need you to be familiar with the Ohms law which states, the direct current flowing in a conductor is directly proportional to the potential difference between its ends.
This divider has two main parts namely the circuit and the equation. To make it work, first, you should secure a circuit by putting in two resistors together. The equation, on one hand, allows you to calculate the output after you have found the ratio of both resistors while considering the input volt as another variable.
Though you can buy your own device, creating a portable one can be a better choice as it helps you save. For this, you have to secure leads, resistors, a 9V battery, alligator clamps, voltmeter and its connectors. In addition, you have to ensure that you get at most the standard battery voltage which is 9.
Start by connecting one lead to a red lead of a 9V battery with an alligator clamp. Then using another lead, do the same steps but this time using the black lead of the connector. After, you can twist the free end of each resistor together.
Make sure that you have provided a solid twist for it by clamping an alligator clamp on it. Then look at the positive and negative terminals of the battery. When found, attach the red wire to the positive and the black wire to the negative. Then turn your meter on.
The positive voltage terminal of your circuit would be the connector which holds the twisted resistors together in place. On one hand, the negative terminal retains to be the negative source. Using the given equation, the new Volt count of your 9V battery goes down to 3V.
When doing this procedure, always see to it that you have unhooked an end of a divider or unplugged your battery to prevent it from draining. More so, be cautious when working with these types of wiring especially the ones which are still plugged into its outlet because it may result in electrocution. In this case, however, there is not much danger in a 9V energy source.
About the Author:
When you are searching for the facts about a voltage divider, come to our web pages. More details are available at http://www.rossengineeringcorp.com/products/measurement/hv-voltage-dividers/hv-voltage-dividers-detailed-info.html now.